David Oliva
RD Appliance Service, Corp. PO Box 234, Bethpage, NY, 11714
Recently RD Appliance Service was briefly confounded by a Miele washer, a W1918, not exactly the latest model. The complaint was that the washer would not spin out the clothing at the end of the cycle, it would leave them sopping wet. Sometimes, if the customer re-ran the cycle the washer would spin. So, armed with all of the necessary technical documentation and diagnostic equipment I ventured out to the home.
Upon arrival I opened up the service manual on my tablet, placed the machine into service mode and proceeded to run a spin test. The tub spun up to high speed without a hiccup. Hmmm, I thought. So I exited service mode and just ran a regular spin cycle, and again the washer spun.
After questioning the customer about her use of the machine I concluded that the machine was sometimes being overloaded and that this was causing it to be unable to balance itself, thus preventing it from spinning.
Not so.
She called back the next day with the same problem, and again when I arrived the problem would not occur. So I needed to do some more in depth research on this issue as this is no “Just replace it” type of washer, they retail for $2000 or more. With some helpful tips from my fellow appliance technicians at appliantology.org I returned armed with more knowledge and we got it figured it.
My father and I both went back on this, two heads and all. I called the customer about an hour before we were going to arrive and had her start a wash cycle. This worked out well because we arrived just at the end of the cycle and found the washer not spinning. Finally! No spin at the end of a regular cycle, no error codes flashing. Set it to a spin only cycle, no spin. Put it in test mode and ran a spin test, no spin. Alright, now we’re getting somewhere.
So, we opened up the front of the machine (thank you Miele for making the whole front panel open on a hinge!) in order to find out if the motor was getting voltage, which would indicate a problem with the motor itself. However, this old Miele technical info does not include voltages for the motor, and the wires are all the same color and not labeled, same goes for the connectors.
We knew it uses a single winding DC motor, but that’s about as in depth as Miele gets regarding the motor. So after exercising our finely honed diagnostic skills we determined which two wires were the motor voltage supply wires and we attached the voltmeter leads to them near the lower electronic (secondary control board).
We once again put the machine into spin and the damn thing started spinning again. This, however, showed us the voltage used by the motor when it is working, and this is crucial information. In case you are interested it uses ~16-20 VDC on tumble, changing polarity as it switches directions, then the voltage ramps up to a whopping 195 VDC on max spin.
Ok, so we know the motor works, but we still don’t know what’s wrong with the washer. We began doing basic diagnostic checks once again, check and clear drain pump trap, check pressure switch hose, etc. Nothing. So we ran another test cycle. This time allowing it to fill and tumble and then move to drain and spin. Aha! Now it won’t spin. It tumbles a little at 16-20 VDC, then stops and won’t spin, no voltage to the motor. Ok, good. I suggest checking the pressure switch again. So my father tapped the pressure switch and voila!, it starts spinning, and reads all the way up to 195 VDC again. Yes! The pressure switch was sticking….sometimes.
So, we’ve replaced the pressure switch and the air trap with the pressure switch hose and that old school, quality German washing machine is running like new once again.
RD Appliance Service, Corp. Long Island Appliance Repair Since 1963. We are committed to constant improvement in our skills as appliance repair technicians. The above is an article detailing some of our self education in matters of appliance repair diagnostics, an area in which we strive to be the best in the business. If you need an appliance repair anywhere in Nassau County call RD Appliance Service, Corp. at 516-561-0523 or visit our website at http://www.rdapplianceservice.com.
RD Appliance Service, Corp. 